| Customization: | Available |
|---|---|
| After-sales Service: | Quality Assurance |
| Warranty: | 1 Year |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Introduction to oil production line
1.The process of pretreatment
Cleaning:remove most impurities from the material, such as stones, dirt, etc., to prepare for the next crushing
process, improve crushing efficiency and extend machine life.
Crushing:after the crushing process, the material is broken into small pieces, which improves the efficiency of
the material being pressed.
Softening process:Increase the moisture content and temperature of the material, and ultimately increase the
final oil output of the material.
Flaking process:the material is pressed into pieces in this process to increase the amount of oil discharged from
the material.
Oil press:the treated oil enters the squeegee from the hopper. Under the condition of high pressure, the embryo
is continuously pushed inward by the screw press, and is pressed to finally produce oil.
| Residual oil in cake |
≤5% |
| Handing capacity |
500kg-50T/H |
| Crude oil moisture and volatile matter |
≤0.3% |
| Power consumption |
≤15KWH/T |
| Steam consumption |
≤120KG/T(0.8MPA) |
| Mechinical impurities |
≤0.3%(adjustable) |
| Moisture in crude oil |
≤0.2%(qualified detonated experiment) |
Extraction→DTDC→Evaporation→Stripper→Crude oil
Extraction:The solvent enters the material and extracts the oil inside the material under a certain temperature
and pressure.
DTDC:It consists of seven layers. In the first three layers, the wet mash is heated and heated by indirect steam
to pre-dissolve and remove a large amount of solvent. In the next two layers, stripping is carried out under the
action of direct steam, the sixth layer is dried with hot air, and the seventh layer is cooled.
Evaporation:The difference between the boiling point of the oil and the solvent is used to separate the solvent
and the oil.
Stripper:The separated solvent can be dissolved in the selected paraffin or solvent and recovered.
The operating principle of the oil extraction process
(a) At a certain speed, the material is transported clockwise, and the solvent enters the material counterclockwise,
so that the solvent and the material can be contacted to the greatest extent, and the oil yield is improved.
(b) In DTDC, in the evaporation stage, the solvent is evaporated as much as possible, and the solvent is recycled
to recycle. Then in the stripping stage, the amount of solvent in the final oil is less than the local specified amount.
(c) The most important thing in the whole process is to control the temperature. Because the boiling point of the
solvent and oil are different, so the temperature is controlled, then the quality of the obtained oil will be very good.
Do the work of exhaust gas generated during the process of recycling and leaching to protect the environment.
|
Moisture of extraction material |
5-8% |
|
Temperature of extraction material |
50-55°C |
|
Oil content of extraction material |
14-18% |
|
Thickness of extraction cake |
less than 13mm |
|
Powder porosity of extraction material |
less than 15% (30 mesh) |
|
Solvent |
national standard No. 6 solvent oil |
|
Volume of supplement water |
1-2m/t raw material |
Advatage
(1) High oil yield , obvious economic benefit.
(2)Residual oil rate in the dry meal is low.
(3)Improving the quality of the meal and oil.
(4)Low processing cost , high labor productivity.
(5)High automatic and labor saving.
And more other advantages please contact me now,we will provide profession program for you,and we accept custom according your requirements.
FAQ
1.Q:Which kind of oil materials can be processed?
A: All kinds of oil seeds. For example of common oil material:soybean, rice bran, corn germ, cottonseeds,
peanut, sunflower, rapeseed, palm fruit etc.
2. Q:What's the input capacity of your machinery?
A: 5-2000 tons per day. the input capacity is according your plan or requirements to customized.
3. Q:The materials of your machinery?
A: The stainless steel and carbon steel.
4.Q:How should I do if meet some trouble while using?
A:we can supply English manual book and also take a video for showing how to resolve the problems or
dispatch our worker to your factory.
5. Q:Can you install the machine in local place?
A: We will send our engineers to local place to help installing the machine and provide technical guidance.
6.Q:how long can we receive the goods?
A:delivery about 45 working day after your order,have different shipping time of different machinery,and
we will inform you shipping time based on your seaport.
){kind=link}